CDP 6800 Series Low Flow Booster Pump

 Distinguishing Features

  • Toughest, most durable pump on the market
  • Adjustable maximum outlet PSI regardless of feed pressure
  • Expels trapped air - pump will not air lock
  • Can be mounted with pump head up or down
  • More flow at extremely low inlet pressures
  • New motor venting system to remove moisture
  • EMI/RFI electronic noise suppression
  • 100% quality assurance performance tested
.

 Key Operating Benefits

  • Boosts pressure 40 to 120 PSI (adjustable)
  • Fixed pressure to 160 PSI
  • Up to 30,000+ operating hours
  • Whisper quiet - less than 45 DBA
  • Can run dry without damage
  • Self-priming with a 60 inch lift capability
  • Low voltage (12-24 volts) for maximum safety
  • Corrosion resistant exterior
  • Continuous or intermittent operation

 Technical Specifications

  • OPERATION: The 6800 is designed to operate with a PSW Tank Shut-Off Switch for hydro-pneumatic storage systems. The PSW, when used with a typical under-counter R.O. system, can be augmented with an ESO Electronic Shut-Off Valve. It is also compatible with most hydraulic shut-off valves. For counter-top systems, Aquatec's TLC Tank Level Control Switch Valve shut off feed water and the pump when the product water storage tank is full.

  • POWER: Pumps operate with low energy (only 14 watts), low voltage (12-24 volt) motors, powered with compatible transformers with world wide primary voltages available (100 VAC, 120 VAC, 230 VAC). Transformers are optional and must be ordered in addition to the pump.

  • MOUNTING PLATES: The "flexible or steel" base plates are included at no extra cost. The "Universal" base plate P/N 51-104 is available optionally at additional cost.

  • FITTINGS: Built-in 1/4" John Guest half cartridge fittings eliminate need for external fittings (unless elbows are required); 1/4" Jaco straight, 1/4" Jaco elbow fittings, or 8mm stem adapters for metric tubing are optionally available.

  • INSTALLATION: The location and positioning of the pump may affect its' performance. Always consult the factory for recommendations that will optimize your system.

CAP 8800 Series High Flow Booster Pump

 Distinguishing Features

  • Toughest, most durable pump on the market
  • Adjustable maximum outlet PSI regardless of feed pressure
  • Expels trapped air - pump will not air lock
  • Can be mounted with pump head up or down
  • More flow at extremely low inlet pressures
  • New motor venting system to remove moisture
  • EMI/RFI electronic noise suppression
  • 100% quality assurance performance tested
.

 Key Operating Benefits

  • Boosts pressure 40 to 120 PSI (adjustable)
  • Used with membranes 50 to 100 GDP
  • Up to 15,000+ operating hours
  • Quiet - less than 52 DBA
  • Can run dry without damage
  • Self-priming with a 60 inch lift capability
  • Low voltage (12-24 volts) for maximum safety
  • Corrosion resistant exterior

 Technical Specifications

  • OPERATION: The CDP 8800 is designed to operate with a PSW Tank Shut-Off Switch for hydro-pneumatic storage systems. The PSW when used with a typical under-counter R.O. system, can be augmented with an ESO Electronic Shut-Off Valve. It is also compatible with most hydraulic shutoff valves. For counter-top systems, Aquatec's TLC Tank Level Control Switch Valve shut off feed water when the product water storage tank is full. The AFR Auto-Flush Valve is highly recommended for higher production membranes requiring a CDP 8800, to ensure membrane efficiency.

  • POWER: Pumps operate with safe, low energy (only 24 watts), low voltage (12-24 volt) motors, powered with compatible transformers with world wide primary voltages available (100 VAC, 120 VAC, 230 VAC). Transformers are optional and must be ordered in addition to the pump.

  • MOUNTING PLATES: The steel base plate is included at no extra cost. The "Universal" base plate P/N 51-104 is optionally available at no additional cost

  • FITTINGS: Built-in 3/8" John Guest half cartridge fittings eliminate need for external fittings (unless elbows are required); Optional at no cost are 3/8" Jaco straight, 3/8" Jaco elbow fittings, or 8mm stem adapters for metric tubing.

  • INSTALLATION: The location and positioning of the pump may affect its' performance. Always consult the factory for recommendations that will optimize your system.

CAP 8800 Series High Flow Booster Pump - Model 881X-132X-XX - Performance Curves

Continue
Our On-Line Store
Quick Find
 
Use keywords to find any product listed in our store.
Advanced Search
0 items

  Thursday 15 November, 2018     664846 requests since Sunday 24 June, 2012  

Copyright © 2018 - AMPAC USA - All Rights Reserved
Site Map -  Powered by SoapStone Software v2.3.4